Plumbing for Beginners: The Essentials for Bathtub Installation
Plumbing for Beginners: The Essentials for Bathtub Installation
Blog Article
This post below on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is truly intriguing. Try it and draw your own personal assumptions.
Mounting a tub isn't precisely rocket science, but it does need solid plumbing, carpentry, and occasionally, tiling skills. Changing an old bath tub with a new one is additionally a reasonably challenging project. If the old bathtub is readily accessible, the task can move speedily; if you need to open a wall surface to remove the old bathtub as well as place the new tub, the job is much harder. In either instance, the project is within a house handyman's skills, although you will certainly require a helper to move out the old bathtub and also set in the new one. Make sure you have certified on your own for the work and are comfortable trying it. Instead of hiring a service provider to take control of a halfway-completed job, it is far better to think about employing one before you start. Chances are you might need an expert plumber to make tube connections.
This short article will help you install a brand-new tub in your bathroom if you have already purchased a brand-new tub and also do not require to alter the plan of your previous supply of water pipes.
Your devices as well as material list ought to comprise the following:
Planning for the Installment
First of all, the sustaining frame provided with the bathroom ought to be fitted (if needed) according to the manufacturer's guidelines. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is very important to see to it that if the tap features a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets unit to prevent strain on the bathtub.
Fit the flexible faucet ports to the bottom of both taps utilizing 2 nuts and olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet through the hole in the bath. Make use of the nut provided by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you use every one of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath ought to currently prepare to be fitted in its final position.
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installation, then the first thing you ought to do is detach the supply of water. After doing so, switch on the taps to drain pipes any type of water remaining in the system. The process of getting rid of the existing taps can be quite bothersome as a result of the limited gain access to that is commonly the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the faucets. Have a cloth prepared for the remaining water that will come from the pipes. Once the supply pipelines have been eliminated, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from turning throughout this process. As soon as the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any kind of old sealing substance.
Prior to proceeding to fit the brand-new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Setting up the Bath tub
Using the two wood boards under its feet, position the bath tub in the required position. The wooden boards are valuable in uniformly spreading out the weight of the tub over the area of the boards rather than focusing all the weight onto four small factors.
The following goal is to guarantee that the bathtub is leveled all round. This can be attained by inspecting the spirit level as well as adjusting the feet on the bath tub until the level reads level.
To set up faucets, fit all-time low of the outermost versatile tap port to the appropriate supply pipe by making a compression join; after that do the exact same for the various other tap.
Activate the water and examine all joints as well as new pipework for leaks and tighten them if needed. Fill the tub as well as also inspect the overflow electrical outlet as well as the regular outlet for leaks.
Ultimately, fix the bath paneling as explained in the supplier's instruction manual. Tiling as well as sealing around the bathtub must wait till the bath tub has actually been used at least once as this will settle it right into its last placement.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic adapter to prevent damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end gives a link to the current supply pipelines.
If you need to fit a monobloc, then you will call for lowering couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next off, position the faucet in the mounting hole in the bath/basin making certain that the washers are in area in between the tap and the sink. Safeguard the tap in place with the producer provided backnut. Once the faucet is securely in position, the supply pipes can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with typical faucet connectors. The previous type ought to be attached to the faucet ends first, tightening just by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bath satisfies the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move enough to crack an inflexible seal, creating the water to penetrate the wall surface in between the bathroom as well as the tiling, bring about complications with wetness and also feasible leakages to the ceiling listed below.
You can pick from a variety of coloured sealers to assimilate your components as well as fittings. They are sold in tubes and cartridges, and also are capable of sealing voids up to a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to constantly fill up the bathtub with water before securing, to enable the movement experienced when the tub remains in usage. The sealant can break rather very early if you do not take into account this movement prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also conveniently offered on the market. It is advisable to fit the floor tiles using water-resistant or water-proof sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were shown that report about Installing A Bathtub from an associate on a different web page. Be sure to take the opportunity to share this blog post if you liked it. Thanks so much for going through it.
Hot water gone? Call. Report this page